Raso, Renzo

Profilbild
E-Mail-Adresse
Geburtsdatum
Projekt
Organisationseinheiten
Berufsbeschreibung
Nachname
Raso
Vorname
Renzo
Name
Renzo Raso

Filter

2012 - 20153
Filter zurücksetzen

Einstellungen

Autor:in: Schumacher, Christoph M. ×

Suchergebnisse

Gerade angezeigt 1 - 3 von 3
  • Vorschaubild nicht verfügbar
    Publikation
    Template-particle stabilized bicontinuous emulsion yielding controlled assembly of hierarchical high-flux filtration membranes
    (American Chemical Society, 2015) Hess, Samuel C.; Kohll, A. Xavier; Raso, Renzo; Schumacher, Christoph M.; Grass, Robert N.; Stark, Wendelin J. [in: ACS Applied Materials & Interfaces]
    A novel solvent-evaporation-based process that exploits template-particle stabilized bicontinuous emulsions for the formation of previously unreached membrane morphologies is reported in this article. Porous membranes have a wide range of applications spanning from water filtration, pharmaceutical purification, and battery separators to scaffolds for tissue engineering. Different situations require different membrane morphologies including various pore sizes and pore gradients. However, most of the previously reported membrane preparation procedures are restricted to specific morphologies and morphology alterations require an extensive optimization process. The tertiary system presented in this article, which consists of a poly(ether sulfone)/dimethylacetamide (PES/DMAc) solution, glycerol, and ZnO-nanoparticles, allows simple and exact tuning of pore diameters ranging from sub-20 nm, up to 100 nm. At the same time, the pore size gradient is controlled from 0 up to 840%/μm yielding extreme asymmetry. In addition to structural analysis, water flux rates of over 5600 L m–2 h–1 are measured for membranes retaining 45 nm silica beads.
    01A - Beitrag in wissenschaftlicher Zeitschrift
  • Vorschaubild nicht verfügbar
    Publikation
    Limestone nanoparticles as nanopore templates in polymer membranes. Narrow pore size distribution and use as self-wetting dialysis membranes
    (Royal Society of Chemistry, 2014) Kellenberger, Christoph R.; Pfleiderer, Florian C.; Raso, Renzo; Burri, Cornelia H.; Schumacher, Christoph M.; Grass, Robert N.; Stark, Wendelin J. [in: RSC Advances]
    Limestone nanoparticles can be used as nanopore templates to prepare porous polymeric films. Their application as membranes is so far strongly limited by the fact that these films are highly hydrophobic. In this study, a simple method is reported to directly produce self-wetting membranes by the template removal method. Triethyl citrate modified polyethersulfone and cellulose acetate membranes were produced using dissolvable limestone nanoparticles as pore templates. The nanoporous polymer films were used as dialysis membranes and characterized by means of buffer exchange rate, molecular weight cut-off, protein adsorption, pore size distribution and water contact angle. The herein prepared membranes were further benchmarked against commercially available dialysis membranes with comparable average pore size. They showed narrow pore size distributions, fast dialysis rates at low protein adsorption and molecular weight cut-off of around 12 kDa. Interestingly, the triethyl citrate modified polyethersulfone membranes displayed only moderate change in pore size distribution as a result of the plasticizer additive compared to pure polyethersulfone membranes. This is a matter of substantial interest considering the fact that additive modifications of membranes produced by the predominant phase inversion process typically show alterations in morphology that lead to undesired changes in membrane performance. Furthermore, dextran recovery analysis proved to meet the specific requirements for dialysis membrane characterization and benchmarking.
    01A - Beitrag in wissenschaftlicher Zeitschrift
  • Vorschaubild nicht verfügbar
    Publikation
    Nanoparticle-assisted, catalytic etching of carbon surfaces as a method to manufacture nanogrooves
    (American Chemical Society, 2012) Schumacher, Christoph M.; Koehler, Fabian M.; Rotzetter, Aline C. C.; Raso, Renzo; Stark, Wendelin J. [in: The Journal of Physical Chemistry C]
    A simple structuring method for graphitic structures based on the catalytic properties of cerium oxide nanoparticles under oxidizing conditions is presented. Highly oriented pyrolytic graphite chips were impregnated with well-dispersed ceria nanoparticles and then treated at elevated temperatures for several hours. Oxidation activities on the particle surface appeared as crystallographically independent traces that were formed on the graphite and provide a simple method to manufacture nanogrooves at large scale. By altering treatment durations and temperatures, the optimal conditions and activity parameters of the particles were determined. A systematic AFM evaluation allowed formulating of a mechanism of the etching process. The findings provide a simple procedure for the patterning of graphitic structures, formation of nanogrooves and thereby a basic tool for material science with respect to the manufacturing of atmospheric nanofilters and ion-selective membranes.
    01A - Beitrag in wissenschaftlicher Zeitschrift