Maintz, Michaela

Lade...
Profilbild
E-Mail-Adresse
Geburtsdatum
Projekt
Organisationseinheiten
Berufsbeschreibung
Nachname
Maintz
Vorname
Michaela
Name
Maintz, Michaela

Suchergebnisse

Gerade angezeigt 1 - 3 von 3
Vorschaubild nicht verfügbar
Publikation

Parameter optimization in a finite element mandibular fracture fixation model using the design of experiments approach

2023-08, Maintz, Michaela, Msallem, Bilal, de Wild, Michael, Seiler, Daniel, Herrmann, Sven, Feiler, Stefanie, Sharma, Neha, Dalcanale, Federico, Cattin, Philippe, Thieringer, Florian Markus

Lade...
Vorschaubild
Publikation

Topology-optimized patient-specific osteosynthesis plates

2022-09-02, Maintz, Michaela, Seiler, Daniel, Thieringer, Florian M., de Wild, Michael

Patient-specific osteosynthesis plates can be used to reduce complications related to bone fracture treatment, such as infection, malocclusion and fatigue fractures of plates and screws. However, the implant design process is tedious. We propose a semi-automatic workflow to computationally design patient-specific titanium osteosynthesis plates for mandibular angle fractures. In this process, the plate stiffness is maximized while the mass is reduced. Two plate designs with different numbers of screw holes (implant #1 with four holes, implant #2 with eight holes) were generated with identical topology optimization settings and compared in a finite element model simulating various biomechanical masticatory loads. Differences in von Mises stresses in the implants and screws were observed. The load case of clenching the jaw on the opposite side of the fracture showed the highest stress distribution in implant #1 and higher peak stresses in implant #2. Stress concentrations were observed in sharp corners of the implant and could be reduced using local stress-based topology optimization. We conclude that the design process is an effective method to generate patientspecific implants.

Lade...
Vorschaubild
Publikation

Fabrication and characterization of PCL/HA filament as a 3D printing material using thermal extrusion technology for bone tissue engineering

2022-02-11, Wang, Fengze, Tankus, Esma Bahar, Santarella, Francesco, Rohr, Nadja, Sharma, Neha, Märtin, Sabrina, Michalscheck, Mirja, Cao, Shuaishuai, Maintz, Michaela, Thieringer, Florian M.

The most common three-dimensional (3D) printing method is material extrusion, where a pre-made filament is deposited layer-by-layer. In recent years, low-cost polycaprolactone (PCL) material has increasingly been used in 3D printing, exhibiting a sufficiently high quality for consideration in cranio-maxillofacial reconstructions. To increase osteoconductivity, prefabricated filaments for bone repair based on PCL can be supplemented with hydroxyapatite (HA). However, few reports on PCL/HA composite filaments for material extrusion applications have been documented. In this study, solvent-free fabrication for PCL/HA composite filaments (HA 0%, 5%, 10%, 15%, 20%, and 25% weight/weight PCL) was addressed, and parameters for scaffold fabrication in a desktop 3D printer were confirmed. Filaments and scaffold fabrication temperatures rose with increased HA content. The pore size and porosity of the six groups’ scaffolds were similar to each other, and all had highly interconnected structures. Six groups’ scaffolds were evaluated by measuring the compressive strength, elastic modulus, water contact angle, and morphology. A higher amount of HA increased surface roughness and hydrophilicity compared to PCL scaffolds. The increase in HA content improved the compressive strength and elastic modulus. The obtained data provide the basis for the biological evaluation and future clinical applications of PCL/HA material.