Köser, Joachim
E-Mail-Adresse
Geburtsdatum
Suchergebnisse
An origami 3D patterned cellulose-based scaffold for bioengineering cardiovascular applications
Novel Titanium Nanospike Structure Using Low-Energy Helium Ion Bombardment for the Transgingival Part of a Dental Implant
Aim(s): The aim of the study was to fabricate a nanospike surface on a titanium alloy surface using a newly established method of low-energy helium ion bombardment. Various methods to achieve nanospike formation on titanium have been introduced recently, and their antibacterial properties have been mainly investigated with respect to Escherichia coli and Staphylococcus aureus. Oral pathogens such as Porphyromonas gingivalis play an important role in the development of peri-implantitis. For that reason, the antibacterial properties of the novel, nanostructured titanium surface against P. gingivalis were assessed, and a possible effect on the viability of gingival fibroblasts was evaluated. Materials and Methods: Helium sputtering was employed for developing titanium surfaces with nanospikes of 500 nm (ND) in height; commercially available smooth-machined (MD) and sandblasted and acid-etched titanium disks (SLA) were used as controls. Surface structure characterization was performed through scanning electron microscopy (SEM) and atomic force microscopy (AFM). Following incubation with P. gingivalis, antibacterial properties were determined via conventional culturing and SEM. Additionally, the viability of human gingival fibroblasts (HGFs) was tested through MTT assay, and cell morphology was assessed through SEM. Results: SEM images confirmed the successful establishment of a nanospike surface with required heights, albeit with heterogeneity. AFM images of the 500 nm nanospike surface revealed that the roughness is dominated by large-scale hills and valleys. For frame sizes of 5 × 5 μm and smaller, the average roughness is dominated by the height of the titanium spikes. ND successfully induces dysmorphisms within P. gingivalis cultures following the incubation period, while conventional culturing reveals a 17% and 20% reduction for ND compared to MD and SLA, respectively. Moreover, the nanospike surfaces did not affect the viability of human growth fibroblasts despite their sharp surface. Conclusion(s): This study successfully developed a novel titanium-nanospike-based structuration technique for titanium surfaces. In addition, the nanospikes did not hinder gingival fibroblast viability. Enhanced antimicrobial effects for such a novel nanospike-based resurfacing technique can be achieved through further optimizations for nanospike spacing and height parameters.
Rapid prototyping method for 3D printed biomaterial constructs with vascular structures
This paper presents a fabrication method for rapid prototyping of 3D biomaterial constructs with vascular structures. The method relies on poloxamer fugitive ink, which is over casted with a custom-made alginate based model extracellular matrix (ECM). The presented method is simple to implement and compatible with standard cell culture workflows used in biomedical research and pharmaceutical development. We present the material preparation, gelation properties and printing methods in detail. First experiments demonstrate the suitability of the ECM constructs for 3D tissue culture.
Plasma-Etched Nanostructured Polycarbonate Surfaces for Reduced Adhesion of E.coli bacteria
Plasma-etching represents a facile approach to nanostructure polymer surfaces. Here we report on the antibacterial properties of plasma-structured polycarbonate (PC)surfaces. PC foils were structured with O2 plasma and incubated with E.coli. Metabolic activity of adhered live bacteria was quantified with resazurin metabolic indicator. Different incubation times under shaking/resting conditions diminished metabolic activity on structured versus unstructured PC, indicating reduced bacterial adhesion on structured surfaces. Furthermore chemical surface modifications increased metabolic activity on structured compared to unstructured surfaces. Further research on other polymers will be done to analyse the generality of these observations.
An origami like 3D patterned cellulose-based scaffold for bioengineering cardiovascular applications
In this work we describe the manufacturing of cellulosic, cell compatible scaffolds with an inherent 3D origami crease pattern for applications in cardiac tissue engineering. Different cellulosic materials were studied, among them cotton linters, fibers obtained from eucalyptus, pine, spruce and lyocell. Formed sheets made of cotton linters were chosen for further study due to the highest biocompatibility and mechanical properties best suited for cardiomyocytes in wet and dry conditions: E - modulus of 0.8 GPa, tensile strength of 4.7 MPa and tensile strength in wet environment of 2.28 MPa. Cell alignment is desired to achieve directional contraction of the cardiac tissue, and several options were investigated to achieve fiber alignment, e.g. a dynamic sheet former and Rapid Köthen sheet former. Although the orientation was minimal, cells cultured on the cellulose fibers grew and aligned along the fibers. Origami inspired crease patterns were applied to the cellulose scaffolds in order to introduce directional flexibility beneficial for cardiac contraction. The transfer of a Miura-ori crease pattern was successfully applied in two ways: folding of the dried sheet between PET foils pre-formed in a 3D printed mold, and in situ wet fiber molding on a 3D-patterned mesh mounted in the sheet former’s sieve section. The latter approach enables upscaling for potential mass production.
Improved phosphoric acid recovery from sewage sludge ash using layer-by-layer modified membranes
We report an advanced treatment method for phosphoric acid recovery from leached sewage sludge ash. Layer-by-layer (LbL) polyelectrolyte deposition has been used as a tool to modify and convert a hollow ultrafiltration membrane into a nanofiltration (NF) LbL membrane for H3PO4 recovery. To build the LbL membrane, poly(styrenesulfonate) PSS was chosen as polyanion, while three different polycations were used: a permanently charged polyelectrolyte, poly(diallyldimethylammonium chloride), PDADMAC; a pH-dependent charged polyelectrolyte poly(allylamine hydrochloride), PAH; and a PAH modified with guanidinium groups (PAH-Gu). Based on detailed surface characterizations (AFM, XPS and Zeta-potential) it was concluded that both charge density and pH-responsiveness of the polycations are key parameters to control the final membrane surface structure and transport properties. The surface properties of LbL-coated membranes were correlated with the membrane filtration performance, when exposed to the real leached sewage sludge ash solution. The highest permeability was recorded for (PDADMAC/PSS)6, a result that was rationalized on its loose, and possibly less interpenetrated, structure, followed by (PAH-Gu/PSS)6 characterized by a more dense, compact layer. H3PO4 recovery was the highest in the case of (PDADMAC/PSS)6, but the retention of multivalent metals (Fe3+ and Mg2+) was low, leading to a more contaminated permeate. The opposite trend was observed for (PAH-Gu/PSS)6, resulting in a less metal-contaminated, but also a less H3PO4-concentrated permeate. Our LbL-modified membranes were found to improve the permeability and H3PO4 recovery compared to a commercially available acid-resistant NF membrane.
Antimicrobial Polyethylene through Melt Compounding with Quaternary Ammonium Salts
Selected mono- and bicationic quats were compounded with polyethylene. The physicochemical surface properties, leaching behavior, and antibacterial activity of such modified samples were investigated. Contact angle measurements and fluorescein binding assays showed the presence of quaternary ammonium groups at the surface. After storing the samples in 50°C warm water for 30 days, several were still antimicrobially active. No correlation between the number of exposed N+ head groups after leaching and the antibacterial activity was observed. There is however a qualitative correlation of the antibacterial activity with the contact angles and surface concentrations of N+ before leaching/storing in warm water.
Enhanced formation of nanometric titanium cones by incorporation of titanium, tungsten and/or iron in a helium ion beam
Surface patterning of bio-compatible titanium (Ti) shows a growing interest in the medical field. The engineering of material surfaces can achieve bactericidal properties and osteointegration improvements in order to develop medical implants. Spikes-like surface morphologies have already demonstrated the development of promising bactericidal properties. A barely new method to produce nanometric-sized cones on titanium consists of helium (He) ion irradiation using low energies ( 100 eV) and temperatures comprised between 0.25 T/T 0.5 (with T being the melting temperature of the material). Ti, iron (Fe) and/or tungsten (W) were incorporated in a He beam, and their amounts were quantified using X-ray Photoelectron Spectroscopy (XPS). The He ion energy was varied from 70 and 120 eV, the surface temperatures from 571 to 651 K for fluences approximately equal to 1024 m−2. After irradiation, the surface morphology was characterized using Scanning Electron Microscopy (SEM) and Focused Ion Beam (FIB). This study demonstrated the capability for irradiated Ti surfaces to form cones with tunable density, aspect ratio, and heights with the incorporation of Ti, Fe and/or W in a He ion. Additionally, the growth rate of the cones was enhanced by about 30 times in comparison to pure He irradiation as a function of the chosen materials introduced in the He beam.
Phosphorus recovery in an acidic environment using layer-by-layer modified membranes
Phosphorus (P) is a limited natural resource and essential for global food supply, particularly given our ever-growing world population. However, natural P deposits are restricted to just a few countries and the quality of exploited primary sources is declining. Phosphorus recovery from sewage sludge or sewage sludge ash leached by acids is hence gaining importance. During P recovery the removal of impurities is a challenge that can be addressed by nanofiltration retaining e. g. multivalent metals and allowing phosphoric acid to pass. However, currently available membranes show low permeability and limit this process option economically. Layer-by-layer (LbL) membrane synthesis is a technology that allows membrane performance to be tailored to individual filtration tasks. Little is known for such membranes with respect to acid resistance, acid permeability and impurity rejection. We show that LBL membranes based on PDADMAC/PSS show the desired passage of phosphoric acid with retentions values below 10%, aluminum retention was always above 95%. Permeabilities up to 4 L/(m2 h bar) were reached even up to a phosphorous recovery of 75%. Overall permeabilities were 16 times higher than a commercial benchmark membrane. Initial stability tests and upscaling into a larger module show the viability of the proposed modification approach.